Jump to content

Sir Fallsalot

Member
  • Posts

    7,232
  • Joined

  • Last visited

  • Days Won

    42

Everything posted by Sir Fallsalot

  1. ? Why don't you have the like feature on your posts
  2. Sir Fallsalot

    Himalayan

    The early KLR's suffered from carb icing here in the UK my mates was a pain in the arse in the winter
  3. Decided to lake the back end off the bike to tidy it up looking quite rusty under there. When taking the indicators off i had to undo a load of insulation tape around the wires. When investigating why the tape was on there i found for some bizarre reason a previous owner had cut the wires off the indicators and soldered them onto the the opposite one using orange cable to extend them and couldn't even get that right, they had the live going to earth the reason the fuse didn't blow is because the brackets the indicators bolt onto are rubber mounted and are isolated from the frame anyhow i swapped them back the way they were supposed to be minus all the slack that was there I also made this exhaust deflector plate, i got the scott oiler touring kit and noticed when taking things apart it was being melted by the hot exhaust gasses you can see the bow in the number plate where it was catching the exhaust gasses and deflecting them behind the number plate getting everything hot there. This wouldn't happen with the standard exhaust but the venom exhaust is a lot shorter than the standard one This is the back end painted up its not in the best condition hopefully this will preserve it until i strip the whole bike and get it all done properly That was my bank holiday and last weeks evenings taken care of next week is the front end, oil and filter change and i'm going to flush the cooling system no time to get bored here ?
  4. Bob that little reciprocating saw was great at cutting the swing arm bolt off a scrap XR400 frame i bought years ago. I hammered a large screwdriver between the swingarm and frame which gave me enough gap to get the saw blade in, it took a few hours and a couple of blades but it done the job
  5. The rest of the suspension parts were waiting for me when i got home from work last Wednesday thought i'd get it all together that night but forgot i need a new chain slider for the swing arm ordered a genuine one from rugged roads so waiting for that before i put the swing arm on The new bolt i got to replace the one i cut off is a bit awkward to put in as you need to take off the centre stand and to get that off you need to take off the exhaust but i managed to do it by removing the one sleeve on the side the bolt goes in from. Which was a pain to put back in with the springs attached but really didn't want to take the exhaust off or the centre stand springs While waiting for the parts to arrive i made this bracket to stiffen up the back end as it bounces about with the weight of the scottoiler touring reservoir on there. The threaded holes were already in the frame not sure what they were for but were perfect to mount this
  6. The bearing and seal insertion tool i made worked great Bearings pushed in equally each side And now for the seal Everything has now been painted waiting for it to dry and once the collars and bolt arrive from Honda i can reassemble everything
  7. I tried the beating the shit out of it approach first but it was seized to the inner bearing collar, after i cut it all out i tried sledging the bolt out of the collar to see how stuck it was but no movement at all
  8. That unfortunately is not my thing, i try but get bored so easily ?
  9. So to kill some more time i made a tool to press the new bearings and seal back in when they arrive,made from a large bolt. I screwed the nut half way up the bolt and welded in place then cut the head off the bolt, I should have taken the photo before i started All finished the right side is to push the bearing in, the step in the larger diameter is to make sure the bearing is pushed in the correct depth to allow the space for the seal to fit, the left side is to push the seal in flush after the bearing, well that's the theory anyway lol
  10. I've been meaning to strip the rear end off this bike since i bought it in 2010 but only now getting around to it. No play at all in the linkage but not long after i bought the bike i noticed the rear end creaking when getting on and off the bike then it stopped and i forgot about it. As i suspected one of the bearings is seized along with the bolt and another badly corroded bearing. As usual its the most difficult bolt to get at that has seized. Had to strip the swing arm off to get at it and the centre stand has to come off to take the bolt out if it hadn't seized which is a bit of a problem as that's whats holding the bike up but since i'm cutting the bolt it can stay on for now First job is to drill the head off the bolt luckily i had some long cobalt drill bits i bought for a different job a few years ago and long they need to be I started with a small bit and worked my way up to 10mm as that is what diameter the bolt is Didn't take long and the head is off, i had to put a maul grip on the thread the other end to stop the bolt from turning once the head came off so i could drill a bit deeper on the bolt shaft Next was to cut the thread off this would have been a real problem if it wasn't for this little air powered reciprocating saw fitted with a cut down cobalt hacksaw blade, i bought it years ago to cut the swing arm spindle off a scrap XR400 i bought for spares. It took a while but it went through OK Once all cut i used a tyre lever to pry the linkage out And shes out I was quite surprised how good the condition of the rest of the bolts were for a 26 year old bike So the bike was left like this while waiting for parts to arrive
  11. Nothing wrong with that Bob drowning my XR on Salisbury plain cost us about an hour and half to get it going again and me a lot of money to rebuild it afterwards
  12. Nice ride ? but onions with chicken does not compute in my head, i love chicken and i love onions but for some reason eating them together feels like i'll be breaking the law or something ?
  13. Damn shame those pushbikes are dangerous ?
  14. Coming back from Yorkshire a couple of years ago it was 30c me and Specs got stuck in traffic around Oswestry area i think, It was difficult filtering on the bikes with all the gear on Alan suggested we head west a bit before we turned south again which sounded like a good idea but his "a bit" was 30 miles i thought i was going to die of heat exhaustion it wasn't nice. hot weather for me is only enjoyably from the shade in a beer garden ?
  15. Cold is the only way i can ride i cant stand the heat so if we get a summer i don't ride that much. Don't like the dust either but as you say its OK if your out on your own or in front ?
  16. Me and a couple of mates out just before the lock down replacing one madness with another seems along time ago now My mate getting used to his DRZ he picked up that week ? The last time we went out this was me the new rear tyre helped this time We had a great day until my mate dropped his DRZ doing a steep hill climb and broke his clutch lever, I'd given him a lecture about being prepared for our trail rides and luckily he has a nice big bag on the back of his bike full of tools or so i thought all that was in there was the important stuff tobacco, papers, phone and wallet so made him think he had to ride it home without a clutch for a few miles before bodging the spare lever i had for my bike on his hope he's learnt a lesson but i'm not holding my breath ?
  17. I seem to remember you having some problem with getting bikes dirty has some new drug been invented that suppresses your polishing OCD ? Nice to see you still getting out ?
  18. I'd just like to say it was a party in my own home with the wife and kids very important to state at this time ?
  19. I've still got everything from the max bikes era i find it really difficult to sell stuff but added this to the collection in 2016
  20. Yes it is, i miss the duel sport rides we used to have he was a good riding buddy now i ride mostly on my own
×
×
  • Create New...

Important Information

Privacy Policy